Professional fire detector test equipment
The A119 series gives fire alarm contractors, service teams and distributors a focused choice: combined smoke and heat testing, smoke-only testing, or heat-only testing.
Featured combined tester
For teams responsible for mixed detector portfolios, the A119-YW family combines smoke simulation and heated-air testing. Two documented configurations are available, and their battery, housing and pole data must be confirmed separately.
The blue product shown on this website. Its supplied manual identifies an aviation-aluminum body and a 7.4 V battery platform.
A separate documented configuration using a 3.7 V / 2600 mAh battery and a telescopic pole extending to 3 m. Its specifications should not be mixed with YWS01 data.
Compare both configurationsA119 product family
Select the model according to the detectors you maintain. Final configuration, accessories and documentation should be confirmed against the current quotation and supplied manual.
Combined functional testing for teams maintaining both smoke and heat detectors.
A smoke-focused configuration for routine functional checks of compatible smoke detectors.
A heat-focused configuration for functional checks of compatible heat detectors.
Buying guide
Send these project details with your enquiry so the model, pole, battery and accessories can be confirmed before quotation.
List smoke detectors, fixed-temperature heat detectors, rate-of-rise detectors or a mixed portfolio.
Provide typical and maximum ceiling heights, including any atrium, warehouse or stairwell locations.
Estimate tests per day and whether the equipment is for commissioning, scheduled inspection or troubleshooting.
State the importing country and the exact documents, language, packaging or OEM marking required.
Model comparison
| Model | Smoke testing | Heat testing | Recommended use |
|---|---|---|---|
| A119-YW | Yes | Yes | Mixed sites and multi-service contractors |
| A119-Y | Yes | No | Smoke detector inspection programs |
| A119-W | No | Yes | Heat detector inspection programs |
Field applications
Functionally check installed detectors before system handover and document the result.
Support scheduled detector checks in offices, hotels, warehouses, schools and public buildings.
Confirm whether a detector responds during troubleshooting, subject to the system procedure.
A simple field workflow
Always follow the detector manufacturer’s instructions, the A119 manual and the applicable inspection procedure.
Identify the detector type and select A119-YW, A119-Y or A119-W.
Position the tester correctly and run the appropriate smoke or heated-air function.
Confirm detector and system response, then reset and record the test result.
Documentation and delivery
A professional quotation should identify the full suffix, pole configuration, charging accessories, operating document and any project-specific marking.
Model suffix, housing material, battery platform, working reach and intended detector types.
Current manual revision, safety instructions and the correct operating sequence for the supplied configuration.
Pole sections, charger, transport case and consumables should be listed explicitly on the quotation.
Product marking, packaging language and documentation scope can be discussed before production confirmation.
For importers and distributors
Match the functional configuration, accessories and target detector types before ordering.
Discuss product marking, packaging and documentation for distributor programs.
Request the current manual, configuration statement and available evidence for the exact model.
Frequently asked questions
A119-YW is the combined configuration. Confirm the supplied accessories and exact operating procedure before ordering.
A119-Y is the smoke-test configuration. A119-W is the heated-air configuration for heat detector testing.
No. A functional response check is not a substitute for laboratory testing, calibration, system commissioning or the inspection requirements applicable to the site.
Contact Wanlin with the model, destination country, quantity, branding requirements and required documents for confirmation.
Provide the detector types, maximum working height, estimated quantity, destination country, preferred housing, required accessories and any document or OEM requirements.
No. They are separate documented configurations with different housing, battery and pole data. Confirm the complete suffix and current manual revision before ordering.
No. The A119 series supports functional response checks. It does not replace detector calibration, laboratory conformity assessment, system commissioning or the complete inspection procedure required for the site.
Project enquiry
Send the detector types, working height, quantity, destination market and preferred model. We will confirm the suitable A119 configuration, accessories and current document set.
Certification and programme detail
Each topic has its own page with the tables, document list and boundary statements an inspecting authority or distributor needs.
CE, UL 268A, EN 54, NFPA 72, BS 5839 and AS 1851: what each standard covers, which models apply and which document to request.
Certification matrixRoutine maintenance inspections, acceptance testing, training centres, and distribution or private-label programmes.
Field applicationsPrivate-label branding, packaging, voltage and plug adaptation, firmware configuration and certificate documentation.
OEM programmeThe Shenzhen source factory behind the A119 series: in-house research, production and export track record.
Company profileThe questions overseas buyers ask before ordering: certificates, MOQ, samples, lead time and shipping.
All questions